| MODEL | RPS-60-S12 | RPS-60-S24 | RPS-60-S48 |
| OUTPUT | DC Output | 12V | 24V | 48V |
| Rated Current | 5A | 2.5A | 1.25A |
| Current Range Note 1 | 0~5A | 0~2.5A | 0~1.25A |
| Ripple and Noise Note 2 | 10~50℃ | ≤60mV | ≤50mV | ≤120mV |
| -25~10℃ | ≤120mV | ≤100mV | ≤240mV |
| Voltage ADJ. Range | 12~14V | 24~28V | 48~56V |
| Voltage Accuracy | ±1.0% |
| Line Regulation | ±0.5% |
| Load Regulation | ±1% |
| Set-up Time | <1.5S @230Vac Full load |
| Hold up Time | ≥20mS @230Vac Full load |
| Temperature Coefficient | ±0.03%/℃ |
| Overshoot and Undershoot | <5.0% |
| INPUT | Voltage Range | 90Vac~264Vac, 127VDC-370VDC(input V+ connect L, input V- connect N) |
| Frequency Range | 47Hz~63Hz |
| Efficiency (Typical) @230Vac | 86% | 88% | 89% |
| AC Current (max.) | <1.6A |
| Inrush Current (Typical) | 65A/230Vac Cold start | 50A/230Vac Cold start | 65A/230Vac Cold start |
| Leakage Current | Input—output: ≤0.25mA Input—PE: ≤3.5mA |
| PROTECTION | Over Load | 6~7.5A
Hiccup mode, auto recovery | 3~4A
Hiccup mode, auto recovery | 1.5~2.5A
Hiccup mode, auto recovery |
| Over voltage | 15.4~18V
Hiccup mode, auto recovery | 28.8~31.2V
Hiccup mode, auto recovery | 58~63V
Hiccup mode, auto recovery |
| Short Circuit | Long-term mode, auto recovery |
| ENVIRONMENT | Operatingamb.Temp.&Hum. | -25℃~50℃; 20%~90%RH No condensing |
| Storage Temp. & Hum. | -40℃~85℃; 5%~95%RH No condensing |
SAFETY&
EMC
Note 3 | Safety Standards | UL60950, EN60950 |
| Withstand Voltage | Primary-Secondary: 3KVac/10mA; |
| Primary-PE: 1.5KVac/10mA; |
| Secondary-PE: 0.5KVac/10mA |
| Isolation Resistance | >10M ohms |
| EMC Emission | Compliance to EN55022, EN55024 Class B |
| Harmonic Current | Compliance to EN61000-3-2，CLASS A |
| EMC Immunity | Compliance to EN61000-4-2,3,4,5,6,11; heavy industry level |
| OTHERS | MTBF (MIL-HDBK-217F) | 590,000Hrs (25℃, Full load) |
| Dimension (L*W*H) | 103.7*32*97.5mm |
| Cooling method | Cooling by free air convection
|
| NOTE | 1. All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature.
2. Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor.
3. The power supply is considered as a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies” on www.rievtech.com. |
