| MODEL | RPS-15-S12 | RPS-15-S24 |
| OUTPUT | DC Output | 12V | 24V |
| Rated Current | 1.25A | 0.65A |
| Current Range Note 1 | 0~1.25A | 0~0.65A |
Ripple and Noise
Note 2 | 10~70℃ | ≤120mV | ≤120mV |
| -25~10℃ | ≤240mV | ≤240mV |
| Voltage ADJ. Range | 12~14V | 24~28V |
| Voltage Accuracy | ±1.0% |
| Line Regulation | ±0.5% |
| Load Regulation | ±1% |
| Set-up Time | <1.5S @230Vac Full load |
| Hold up Time | ≥20mS @230Vac Full load |
| Temperature Coefficient | ±0.03%/℃ |
| Overshoot and Undershoot | <5.0% |
| INPUT | Voltage Range | 90Vac~264Vac, 127VDC-370VDC |
| Frequency Range | 47Hz~63Hz |
| Efficiency ( Typical) | 83% @230Vac input, full load | 84.5% @230Vac input, full load |
| AC Current (max.) | <0.5A |
| Inrush Current (Typical) | 50A/230Vac Cold start |
| Leakage Current | Input—output: ≤0.25mA Input—PE: ≤3.5mA (264Vac input, 63Hz) |
| PROTECTION | Over Load | 1.5~2.0A, hiccup mode, auto recovery | 0.7~1.0A, hiccup mode, auto recovery |
| Over voltage | 15.0~16.8V,Constant voltage,
auto recovery | 28.8~31.2V,Constant voltage,
auto recovery |
| Short Circuit | Long-term mode, auto recovery |
| ENVIRONMENT | Operating amb.Temp.&Hum. | -25℃~70℃; 20%~90%RH No condensing |
| Storage Temp. & Hum. | -40℃~85℃; 5%~95%RH No condensing |
| SAFETY &EMC Note 3 | Safety Standards | UL60950, EN60950 |
| Withstand Voltage | Primary-Secondary:3KVac/10mA;
0.5KVac/10mA |
| Primary-PE:1.5KVac/10mA; |
| Secondary-PE:0.5KVac/10mA |
| Isolation Resistance | >10M ohms |
| EMC Emission | Compliance to EN55022, EN55024 Class B |
| Harmonic Current | Compliance to EN61000-3-2，CLASS A |
| EMC Immunity | Compliance to EN61000-4-2,3,4,5,6,11; heavy industry level |
| OTHERS | MTBF (MIL-HDBK-217F) | 590,000Hrs (25℃, Full load) |
| Dimension(L*W*H) | 103.7*32*97.5mm |
| Cooling method | Cooling by free air convection
|
| NOTE | 1. All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature.
2. Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor.
3. The power supply is considered as a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies” on www.rievtech.com.cn. |
